If your rented flat is heated by district heating or a shared boiler, there is a deadline coming up. Under EU energy-efficiency rules, heat meters, hot-water meters and heat cost allocators that cannot be read remotely have to be upgraded or replaced by 1 January 2027. The only exception is where it is shown not to be cost-efficient.

That is seven weeks from now (mid-November 2026). Many buildings are still sorting out their devices, so technicians will be visiting flats in December, and some of those flats have tenants living in them. This guide covers what to check and how to handle the swap without a dispute at the next heating settlement.

Where the rule comes from

The requirement comes from the EU Energy Efficiency Directive, as amended by Directive (EU) 2018/2002. Since 25 October 2020, newly installed meters and heat cost allocators have had to be remote-readable. Older devices must be made remote-readable or replaced by 1 January 2027, unless the member state shows this is not cost-efficient. "Remote-readable" means the device can be read without anyone entering the flat. Usually that is by radio, sometimes from a walk-by receiver in the stairwell.

The rule covers heating, cooling and domestic hot water. It does not cover cold-water meters. Every member state has written the rule into its own law, so the details differ from country to country.

Hungary: Decree 676/2023 and the building's duty

In Hungary the rules were published on 29 December 2023 in two government decrees: 676/2023 for central (building-level) heating and 677/2023 for district heating, which amended the district heating rules. Section 33(2) of Decree 676/2023 says devices installed before the decree that cannot be read remotely must be made remote-readable or replaced by 1 January 2027 at the latest.

The main points:

  • It is the building's job, not yours alone. The installation is organised for the whole building, usually by the condominium (társasház) or housing cooperative through its common representative. The decree also requires all cost allocators in a building to be readable through the same system, so individual owners cannot each pick their own.
  • Cost-efficiency test. A building can be exempt if installation is technically not feasible or not cost-efficient. That has to be shown by an analysis under the decree's annex. Telex reported that this involves three comparable contractor quotes, weighed against expected savings over ten years. If the analysis finds installation worthwhile, the work must be done within a year, and still by 1 January 2027.
  • One-pipe flow-through heating. In buildings with one-pipe flow-through heating, common in older panel blocks, residents cannot regulate radiators individually. According to Telex and Ezermester, these buildings are exempt from heat cost allocators, but hot-water meters must still be remote-readable. One-pipe systems with a bypass section are not covered by this exemption. Have a heating engineer confirm which kind your building has.
  • Cold-water meters are not covered. The building may choose to swap them at the same time, but the law does not require it.
  • Penalty. For district-heated buildings, sources report that if remote reading is feasible and cost-efficient but not installed, heating can be billed at 2.5 times the normal charge.

Short notes on other countries

The principle is the same everywhere, but deadlines, exemptions and penalties differ. Always check your own country's rules.

  • Germany: under § 5(3) of the Heizkostenverordnung, devices must be remote-readable by 31 December 2026. There is no fine, but tenants may cut their heating-cost share by 3% for each year the upgrade is missing. Cold-water meters are not affected.
  • Czechia: the duty is in the energy management act (zákon č. 406/2000 Sb.). From 1 January 2027 residents must receive monthly consumption information, and buildings that do not comply risk fines of up to CZK 200,000.
  • Ireland: S.I. No. 630/2022 requires existing meters and heat cost allocators to be made remote-readable or replaced by 1 January 2027, except where guidelines from the regulator provide an exemption.

If you let property in another EU country, ask your building manager which national law applies there.

What to do in the next few weeks

1. Ask the building manager two questions

Which devices are in your flat, and are they already remote-readable? If not, when is the swap? Also ask whether the building did a cost-efficiency analysis or claims an exemption, such as one-pipe heating. Get the answer in writing, by email or in the meeting minutes.

2. Arrange access with your tenant in writing

The technician needs to get to every radiator and to the hot-water meter. Tell your tenant the date and time window as early as you can, explain what will be done and how long it should take, and ask who will let the technician in. Most leases and national rules allow access for necessary work after reasonable notice, but check what yours say. A written message avoids "nobody told me" later, and a missed appointment in December may not get a second slot before the deadline.

3. Check who pays before passing anything on

In a condominium, the installation is normally decided by the owners and charged to them, often through the common charges. Whether you can pass any of it on to your tenant depends on your lease and national law. As a rule, buying and installing equipment is an owner's cost. Ongoing reading or data fees may be different if your lease lets you pass on utility-related costs. Do not add a new charge to the tenant's bill until you have checked this.

4. Record old and new device numbers and readings

On the day of the swap, write down or photograph:

  • the serial number and final reading of each old device,
  • the serial number and starting reading of each new device,
  • which radiator or meter each one belongs to, and the date.

Ask the technician for the installation report and keep a copy. The next heating settlement will combine readings from the old and new devices, and if something looks wrong, these numbers are your evidence. They also help if a tenant moves out mid-season.

If you use LeasingTrack, you can arrange the visit through the tenant messages and store the swap report and photos with the property's documents. That way they are all in one place when the settlement arrives.

If there is a dispute

Arguments over access, cost sharing or a settlement that looks off are best settled calmly and in writing. If the building, your tenant and you cannot agree, or the amounts are significant, check your individual case with a lawyer, or with an accountant for tax questions about passing on costs. The rules differ by country and sometimes by building, and the right answer depends on your lease.